You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
147 lines
37 KiB
147 lines
37 KiB
id&qtp&qim&qil&qtx&qca&qia&qrm&qnxt&qprv&qalb&subj&wght&pts&flr&ded&layout&qfixed&qptsbyans&flags
|
|
cdc6.001&mcs&0&Y&The MICR field that rejects most often is the &Amount field.&On-Us field.;Transit Number field. ;Auxiliary On-Us field. ;&&&&n&VI-D-2.0&&&&
|
|
cdc6.002&mcs&0&Y&If there is a refolding problem with a one- part continuous form, which of the following is the most likely cause? &Paper weight is too light &Platen is too hard ;Vertical perfs are too tight ;Paper tension is set too high ;&&&&n&VI-A-1 .0&&&&
|
|
cdc6.003&mcs&0&Y&Typical reasons for check rejection by MICR reader/sorters are &debossment, character skew, and voids. &carbonized band, voids, and debossment. ;character skew, signature interference, and paper curling.;character dimension, signature interference, and embossment. ;&&&&n&VI-D-2.0&&&&
|
|
cdc6.004&mcs&0&Y&Which of the following are acceptable for use in laser printers? &Offset and ledger papers &Coated papers with waxy surfaces ;Papers with plastic additives ;Papers that have been embossed ;&&&&n&VI-A-2 .0&&&&
|
|
cdc6.005&mcs&0&Y&Bursters that process two-wide forms should be equipped with&a center slitter.&tractors.;trim baskets.;a forms counter.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.006&mcs&0&Y&Which of the following is most descriptive of thermal printers?&They require special paper&They are page printers;They can handle up to six parts;They produce a letter quality image;&&&&n&VI-A-2.0&&&&
|
|
cdc6.007&mcs&0&Y&Which of the following applications is ideal for printing on an ink jet printer?&Direct mail adresses&Plastic card stock;Checks with MICR;Multiple-part forms;&&&&n&VI-A-2.0&&&&
|
|
cdc6.008&mcs&0&Y&Which of the following properties of a pressure-sensitive label need NOT be considered for the label to be scanned?&Adhesion&Opacity;Color;Reflectance;&&&&n&VI-D-1.0&&&&
|
|
cdc6.009&mcs&0&Y&Which of the following is a major forms concern when using laser printers?&Heat-resistance of ink&Speed of printing;Low print resolution;Small variety of print fonts and graphics;&&&&n&VI-A-2.0&&&&
|
|
cdc6.010&mcs&0&N&Thermal transfer printing differs from laser printing because thermal transfer requires&a ribbon to produce an image.&heat to produce an image.;impact to produce an image.;pressure to produce an image.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.011&mcs&0&N&The function of a burster bar on a multipart burster is to&help to break between-set perfs.&control static.;provide infeed control tension.;prevent double feeds.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.012&mcs&0&Y&What is the primary drawback to ion deposition (electron beam imaging) printing when compared to laser printing?&&&&&&n&.0&&&&&1&&&N.
|
|
cdc6.013&mcs&0&N&Which of the following is a major problem when photocopying onto standard chemical carbonless copy paper?&Copier contamination&Hardened capsules;Toner adhesion;Paper sequence;&&&&n&VI-A-2.0&&&&
|
|
cdc6.014&mcs&0&N&When a burster-imprinter is used, a separate imprinting cylinder for each form length is usually necessary because&imprinting is a rotary operation.&the imprinter is attached to a burster.;the area that can be imprinted is limited.;imprinting is done from raised metal or rubber type.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.015&mcs&0&N&Which of the following print mechanisms is NOT normally found on high-speed printers?&Daisy wheel&Drum;Laser;Chain;&&&&n&VI-A-1.0&&&&
|
|
cdc6.016&mcs&0&N&Which of the following is characteristic of laser printers?&They can use either plain sheet paper or preprinted forms requiring special ink&They can use plain sheet paper only;They must use continuous stock forms;They must use a special paper to receive the charge stylus;&&&&n&VI-A-2.0&&&&
|
|
cdc6.017&mcs&0&N&If a client prints a five-part, glued, carbonless form on a 160 CPS dot matrix impact printer and frequently experiences no image on part 1, which of the following is the most likely cause?&The ribbon is being lifted out of position by the outfold between forms&The paper is too porous to accept carbonization;Carbonless paper on part 1 is run coated side up;A thin carbonless coating is present on the face of part 1;&&&&n&VI-A-1.0&&&&
|
|
cdc6.018&mcs&0&N&Which of the following is characteristic of all thermal, electrostatic, photoelectrostatic, and ink jet non-impact printers?&They use dot matrix format&They feed cut-sheet forms;They require special paper;They use imprinted paper rolls;&&&&n&VI-A-2.0&&&&
|
|
cdc6.019&mcs&0&N&When using laser printers, offsetting and machine damage can be prevented by using preprinted forms with&heat resistant inks.&lighter weight papers.;highly calendered papers.;infrared inks.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.020&mcs&0&Y&When computer printing on a peel-back check mailer, which of the following printers would produce the best printing quality?&Impact dot matrix&Laser;Magnetography;Thermal;&&&&n&VI-A-1.0&&&&
|
|
cdc6.021&mcs&0&N&The most common reason for using grain long stock on a high-speed plain paper copier is to&reduce feeding problems.&improve post printing folding.;enhance toner adherence.;improve magnetic qualities in holding an electrostatic image;&&&&n&VI-A-2.0&&&&&1&&&N.
|
|
cdc6.022&mcs&0&Y&Which of the following are ALWAYS impact printers?&Drum and daisy wheel only&Matrix and drum only;Drum and diasy wheel only;Matrix, drum, and daisy wheel;&&&&n&VI-A-1.0&&&&
|
|
cdc6.023&mcs&0&Y&Which of the following is NOT characteristic of waterfall decollators?&They can decollate corner-stitched forms&They can separate carbonless forms;They can separate 4-part forms after only three passes;They can decollate marginally glued forms after the glued margins have been removed;&&&&n&VI-B-2.0&&&&
|
|
cdc6.024&mcs&0&Y&Ink offsets onto forms imaged by a laser printer when&ink builds up on rollers and fuser drum.&large screened areas are used.;there is too much toner in the storage area.;low heat and pressure are generated by printer.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.025&mcs&0&Y&With which of the following types of comptuer printers is framing LEAST likely to be a problem?&Matrix line&Drum;Train;Band or belt;&&&&a&VI-A-1.0&&&&
|
|
cdc6.026&mcs&0&Y&When writing specifications for pressure-sensitive labels for use in a laser printer, it is important to consider that&labels may peel from carrier during imaging.&many ink colors cannot be used.;permanent adhesive must be used.;low tack adhesive is recommended.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.027&mcs&0&Y&Which of the following is the primary benefit of a bar coded piece work ticket system?&Reduction in data entry costs&Elimination of stock-outs in raw materials;Fast reconciliation of inventory discrepancies;Continuous update of manufacturing quality;&&&&n&VI-D-3.0&&&&
|
|
cdc6.028&mcs&0&Y&Impact from the front of a form through the ribbon is characteristic of which of the following types of printers?&Daisy wheel only&Ink jet and drum only;Daisy wheel and drum only;Ink jet, daisy wheel, and durm;&&&&n&VI-A-1.0&&&&
|
|
cdc6.029&mcs&0&Y&Which of the following printers is able to print on the widest variety of surfaces?&Ink jet&Laser;Thermal transfer;Ion deposition;&&&&n&VI-A-2.0&&&&
|
|
cdc6.030&mcs&0&Y&The major advantage of a cutter over a burster is that a cutter can&clean-cut.¢er-slit.;trim off line holes.;handle multipart forms.;&&&&n&VI-B-3.0&&&&
|
|
cdc6.031&mcs&0&Y&In a thermal transfer printer, the color of the variable data image is determined by the &ribbon.&type of paper.;color of ink in the printer paper.;amount of heat applied to the print head.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.032&mcs&0&Y&In a impact dot matrix printer, the characters are formed from&print wires.&thermal heads.;a type bar.;a daisy wheel.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.033&mcs&0&Y&Which of the following is LEAST likely to cause a forms jam resulting from a loss of pinfeed control?&Use of carbonless paper&Hanging punches;An improperly set drag control;Too much horizontal tension on the form;&&&&n&VI-A-1.0&&&&
|
|
cdc6.034&mcs&0&Y&Thermal-transfer printing requires the use of which of the following?&A speciall ribbon&Thermal paper only;Thermal paper and special ribbon;Thermal-resistant ink on preprinted forms;&&&&n&VI-A-2.0&&&&
|
|
cdc6.035&mcs&0&Y&Which of the following printers is most commonly used for word-processing operations?&Daisy wheel&Ink jet;Thermal;Magnetic;&&&&n&VI-A-1.0&&&&
|
|
cdc6.036&mcs&0&Y&Which of the following is characteristic of all non-impact printers?&Images are formed by dots&They are heat sensitive;Forms must be on a roll;They use plain bond papers;&&&&n&VI-A-2.0&&&&
|
|
cdc6.037&mcs&0&Y&Which of the following is NOT a term for "non-scan"?&Nonreflective&Blind;Dropout;Nonread;&&&&n&VI-D-1.0&&&&
|
|
cdc6.038&mcs&0&Y&Before a line-glued form can be decollated, it must be&stripped/trimmed.&burst.;crimped.;perforated.;&&&&n&VI-B-2.0&&&&
|
|
cdc6.039&mcs&0&Y&On a four station decollator, the circumference of the carbon on spindle builds up, causing a speed differential problem and a form sag between stations. If margins are not trimmed, one solution to this problem would be to&disengage the pinfeed tractors.&remove the tension bar.;reduce the decollator speed.;decollate fewer parts on each pass.;&&&&n&VI-B-2.0&&&&
|
|
cdc6.040&mcs&0&Y&How many passes through an A-frame decollator are needed to completely decollate a six-part form?&Five&One;Two;Six;&&&&n&VI-B-2.0&&&&
|
|
cdc6.041&mcs&0&Y&Which of the following continuous forms can NOT be decollated on a horizontal decollator with marginal trimmers?&Coner-stitched forms&Crimp-fastened forms;Marginally glued forms;Cross-web glued mailers;&&&&n&VI-B-2.0&&&&
|
|
cdc6.042&mcs&0&Y&Which of the following is NOT characteristic of forms bursters?&They require no adjustments when changing from one form size to another&They use tension to separate forms;They may require forms with special perforations;They cause smudging when bursting multiple-part sets;&&&&n&VI-B-1.0&&&&
|
|
cdc6.043&mcs&0&Y&When it is necessary to sign a loose-insert check that is enclosed in a continuous mailer, it is best to use an imprinter attachment on&a burster.&a deleaver.;an A-frame decollator.;a check protector.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.044&mcs&0&Y&Computer output microfilm (COM) refers to microfilm computer reports created from&computer output without creating a hard-copy printout.&hard-copy, green-bar paper printouts.;high resolution monitors using a reverse video feature.;hard-copy printouts that have been printed on 15# or 20# blank (no shaded bars) computer paper.;&&&&n&VI-A.0&&&&
|
|
cdc6.045&mcs&0&Y&If a continuous form produced on a line printer has poor quality print on part one, the problem is most likely due to&a worn ribbon.&trapped air within a form.;a defective printer controller.;improper tension on the form.;&&&&n&.0&&&&
|
|
cdc6.046&mcs&0&Y&Which of the following are NORMALLY available as impact printers?&Matrix, drum, and train&Matrix and train only;Drum and train only;Matrix and drum only;&&&&n&VI-A-1.0&&&&
|
|
cdc6.047&mcs&0&Y&Which of the following characterizes matrix impact printers?&Their ink jets tend to clog only&Their ink jets tend to clog and their characters tend to have a serrated (ragged) appearance when printed at high speeds only;Their characters tend to have a serrated (ragged) appearance when printed at high speeds and their characters are all formed from small dots;Their characters tend to have a serrated (ragged) appearance when printed at high speed and they are often plagued by framing;&&&&n&.0&&&&
|
|
cdc6.048&mcs&0&Y&A high-speed printer with print tractors above and below the print mechanism is better than a printer with only one set of tractors because &more constant paper tension is maintained only.&paper can be moved forward or backward only.;more constant paper tension is maintianed and refolding problems are reduced.;paper can be moved forwarded or backward and refolding problems ar reduced.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.049&mcs&0&Y&Which of the following is the LEAST desirable application for ion deposition printing?&Printing on high cotton fiber content letterheads&Bar coding;Business forms printing;Variable data printing;&&&&n&VI-A-2.0&&&&
|
|
cdc6.050&mcs&0&Y&If a printer is producing poor copies because of insufficient impact, which of the following is LEAST likely to solve the problem?&Using a mylar ribbon&Including fewer parts in the form;Adjusting the print density control;Using lighter-weight premium materials;&&&&n&VI-A-1.0&&&&
|
|
cdc6.051&mcs&0&Y&On an impact printer, the number of print positions refers to the&maximum number of characters which can be printed on one line.&number of printable lines per inch.;number of fields designed for variable information.;maximum number of characters on the print head.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.052&mcs&0&Y&In which of the following applications would a leader strip be most useful?&Saving numbered documents&Feeding mailers;Shingling envelopes;Keeping labels from popping off the carrier;&&&&n&VI-A-1.0&&&&
|
|
cdc6.053&mcs&0&Y&Stub margin clearance refers to &distance from center of pin to the inside edge of the tractor.&distance from center of line hole to the center of the first print position.;physical opening between pinfeed tractor belt and bottom of the device that holds the form on the pins.;maximum pin diameter.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.054&mcs&0&Y&If a bar code printed on a label by an impact matrix line printer is to be scanned by a typical infrared LED scanner, which of the following ribbon types should be used on the printer?&Black OCR-ink ribbon&Red acid-etched ink ribbon;Black dye-based ink ribbon;Black thermal-transfer ribbon;&&&&n&VI-A-1.0&&&&
|
|
cdc6.055&mcs&0&Y&Which of the following is primarily an impact printing technique?&Dot matrix&Magnetography;Laser ;Ink jet;&&&&n&VI-A-1.0&&&&
|
|
cdc6.056&mcs&0&Y&Which of the following is considered a major advantage of direct thermal printers for printing bar codes?&High-density, scannable image&Low paper cost;Very stable image;Excellent manifolding;&&&&n&VI-A-2.0&&&&
|
|
cdc6.057&mcs&0&Y&Which of the following is a common problem with ink jet printers?&Clogging&Not good for color graphics;Very expensive;Limited type fonts;&&&&n&VI-A-2.0&&&&
|
|
cdc6.058&mcs&0&Y&Fusing is accomplished in an ion deposition (electron beam imaging) printer by &pressure.&magnetics.;ultraviolet light.;impact.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.059&mcs&0&Y&Which of the following is a major advantage of duplexing on laser printers?&Reduces the amount of paper used&Improves the quality of the back print;Reduces the number of print impressions;Saves toner;&&&&n&VI-A-2.0&&&&
|
|
cdc6.060&mcs&0&Y&When designing perforated forms for high-speed sheetfed laser printers, the forms professional should specify&perforation cut from side to be imaged.&at least 28# ledger.;rough surface sheet to mask perforations.;perforations perpendicular to feed direction.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.061&mcs&0&&If the preprinted image on a form is offsetting on a laser printer, which of the following is the most likely cause of the problem?&Wrong ink is being used&Uncoated paper is being used;Printer is out of adjustment;Form is being stored improperly;&&&&n&VI-A-2.0&&&&
|
|
cdc6.062&mcs&0&N&In thermal-transfer printing, image transfer is caused by a &ribbon and heated matrix print head.&chemical reaction within the paper.;platen on a daisy-wheel type of printer.;chemical reaction among the various parts of a multipart form.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.063&mcs&0&N&Cut sheet forms with heavy ink coverage are being supplied to a service bureau which is imaging these documents on a high-speed laser printer. To meet the client's tight deadline, spray powder is used to hasten the drying time of the offset printed inks. Which of the following is most likely to occur while the service provider is imaging these forms?&Improper fusing of the toner to the paper&Skewing of sheets;Excessive curling of the paper;Offsetting of the preprinted image;&&&&n&VI-A-2.0&&&&
|
|
cdc6.064&mcs&0&&Which of the following best represents the benefit of specifying long grain papers for use in laser printers?&Greater sheet rigidity&Greater sheet flexibility;Better print quality;Better toner adherence;&&&&n&VI-A-2.0&&&&
|
|
cdc6.065&mcs&0&&High speed ink jet imaging is ideally suited for producing&computer-generated variable data.&checks.;long-run process color printing.;short-run printing of fixed data.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.066&mcs&0&&Which of the following is the main advantage of using thermal printers to image pressure-sensitive labels?&On-demand flexibility&High speed;Low paper cost;Long run lengths;&&&&n&VI-A-2.0&&&&
|
|
cdc6.067&mcs&0&&Which of the following is the non-impact printing technology which creates color graphics and highlighting by melting crayon-like solid wax ink to a liquid state before spraying it onto the substrate?&Phase change ink jet&Color laser;Digital color;Direct thermal;&&&&n&VI-A-2.0&&&&
|
|
cdc6.068&mcs&0&&Which of the following best describes direct thermal printing?&The image is created by a chemical reaction as paper is exposed to heat&The heated print head causes ink to transfer from the donor ribbon to the paper;The ribbon rather than the print head gets hot to transfer ink from the donor ribbon to the paper;The heated fuser roller fuses toner to the pages;&&&&n&VI-A-2.0&&&&
|
|
cdc6.069&mcs&0&&If a form cannot be decollated before bursting, smudging may be MINIMIZED by &removing tension bars from burster.&using a hard carbon.;using a burster with metal knurled rollers.;increasing roller pressure.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.070&mcs&0&&An imprinting unit on a burster is most commonly used to print&signatures.&marginal words.;modulus numbers.;consecutive numbers.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.071&mcs&0&N&Trimmer wheels in a burster or decollator are used to &remove the pinfeed margins.&remove the stub on a unit set.;cut the forms along the horizontal perforation.;cut the forms cleanly on all edges to remove any sign of perforations.;&&&&n&VI-B-1 .0& 2.0&&&
|
|
cdc6.072&mcs&0&&Bursters used for detaching continuous forms at the cross perforation usually employ&pressure rollers that rotate at different speeds.&reciprocating shear blades that guillotine cut the forms.;gears engaging the pinfeed margins under stop-and-go operation.;cross-web slitters that cut across the form.;&&&&n&VI-B-1.0&&&&
|
|
cdc6.073&mcs&0&&Which of the following is the most difficult problem to solve in the use of a horizontal decollator?&Static buildup on the down chutes&Carbon buildup on the spindles;Large number of parts required;Forms-fastening requirements;&&&&n&VI-B-2.0&&&&
|
|
cdc6.074&mcs&0&&Which of the following would most likely produce decollating problems?&Lightweight paper&Heavyweight paper;Fugitive glue;Pattern carbon;&&&&n&VI-B-2.0&&&&
|
|
cdc6.075&mcs&0&&On a four station decollator, the circumference of the carbon on spindle builds up, causing a speed differential problem and a form sag between stations. If margins are not trimmed, one solution to this problem would be to&disengage the pinfeed tractors.&decollate fewer parts on each pass.;remove the tension bar.;reduce the decollator speed.;&&&&n&VI-B-2.0&&&&
|
|
cdc6.076&mcs&0&&An A-frame decollator is most appropriate for forms fastened with &crimps.&tape lock.;transfer tape.;spot glue.;&&&&n&VI-B-2.0&&&&
|
|
cdc6.077&mcs&0&&If a perfectly clean-edged sheet is required from a continuous form, which of the following should be used?&Cutter&Burster;Perfecting press;Decollator;&&&&n&VI-B-3.0&&&&
|
|
cdc6.078&mcs&0&&Which of the following can NOT be used to image all parts on an imprinting machine without a ribbon?&Register bond interleaved with carbon &Translucent paper and double-faced carbon;Self-contained paper;Carbon over the face of a carbon-interleaved set;&&&&n&VI-B-4.0&&&&
|
|
cdc6.079&mcs&0&&Which of the following is the best combination of ink and paper for forms that will be microfilmed?&White paper and red ink&White paper and green ink;Yellow paper and brown ink;Goldenrod paper and black ink;&&&&n&VI-B-5.0&&&&
|
|
cdc6.080&mcs&0&&High-speed mail inserters usually require that the piece to be inserted&be at least 1/2 inch narrower than the envelope to be used.&has preprinted fold marks.;be a specific color and weight.;has no special perforations or file holes exposed.;&&&&n&VI-B-5.0&&&&
|
|
cdc6.081&mcs&0&&For papers used in optical character recognition applications, it is most important to have a high level of &reflectance.&absorption.;gloss.;opacity.;&&&&n&VI-D-1.0&&&&
|
|
cdc6.082&mcs&0&&A check fraudulently copied on a color copier will be rejected during the bank's processing because the&check lacks sufficient iron oxide in the MICR line.&bank cannot reconcile the repeated check number.;bank cannot read the microprinting during sorting.;check lacks a chemical watermark.;&&&&n&VI-D-2.0&&&&
|
|
cdc6.083&mcs&0&&MICR rejections occur primarily as a result of &MICR encoding in the Amound field by banks.&debossment of the paper by the manufacturer.;lack of schedule maintenance on reader/sorters by banks.;voids printed by the manufacturer.;&&&&n&VI-D-2.0&&&&
|
|
cdc6.084&mcs&0&&The height of a bar code is usually chosen to &expand or limit the capacity of the bar code.&allow the operator to stay within the bars while scanning;expand or limit the flexibility of the bar code.;conform to software specifications.;&&&&n&VI-D-3.0&&&&
|
|
cdc6.085&mcs&0&&Which of the following is the key advantage of bar coding?&Accuracy of data entry&Unlimited keyboard entry;Low cost hardware;Flexibility of data entry;&&&&n&VI-D-3.0&&&&
|
|
cdc6.086&mcs&0&&Which of the following is an accurate comparison between fixed beam bar code readers and moving beam readers?&The moving beam reader can read alternating horizontally and vertically printed bar codes&The number of read opportunities per pass is the same for each;The moving beam reader is more sensitive to ambient light;The fixed beam has wider depth of field;&&&&n&VI-D-3.0&&&&
|
|
cdc6.087&mcs&0&&Which of the following would provide the lowest first read rate of bar codes placed on the internal plies of a four-part form?&Crash imprinting&Ink jet;Magnetography;Ion deposition;&&&&n&VI-D-3.0&&&&
|
|
cdc6.088&mcs&0&&When a bar code will be exposed to heavy use by a contact reader, the bar code should be &laminated.&printed by an ink jet printer.;scanned with a light-emitting diode.;scanned twice to verify an accurate read.;&&&&n&VI-D-3.0&&&&
|
|
cdc6.089&mcs&0&&Bar codes imaged by ion deposition, magnetography, or laser have which of the following advantages over low density ink jet?&Images with increased edge definition&Images computer generated algorithms;Images at higher speeds;Images with less resolution;&&&&n&VI-D-3.0&&&&
|
|
cdc6.090&mcs&0&&With regard to imaging storage and retrieval, a compression algorithm allows&a decrease in the amount of media space required to store a scanned image.&an oversize document to be displayed on a regular monitor.;an increase in the speed at which a document scanner scans a document.;an enhancement in the quality of the displayed image by filling in half tones.;&&&&n&VI-D-4.0&&&&
|
|
cdc6.091&mcs&0&&Which of the following would be the most efficient bar code scanner for a warehouse with a high speed conveyor belt that contains bar coded packages?&Holographic&Long-range;Fixed position;Hand held;&&&&n&VI-D-4.0&&&&
|
|
cdc6.092&mcs&0&&When scanning text which will be edited, which of the following types of scanning software would be most appropriate?&Character&Bar code;Mark;Magnetic;&&&&n&VI-D-4.0&&&&
|
|
cdc6.093&mcs&0&&The most important element in allowing an ink to drop out on a scannable form is the &light source used in the scanner.&color of paper on which the form is printed.;reflectance of the paper on which the form is printed.;imaging system being used.;&&&&n&VI-D-4.0&&&&
|
|
cdc6.094&mcs&0&N&A LAN is primarily used to physically link&workstations with a file server.&workstations in remote locations.;distributed printing.;telecommunications devices.;&&&&n&IV-D-5.0&&&&
|
|
cdc6.095&mcs&0&&As it relates to the magnetic stripes used on plastic cards, "coercivity" describes the &stripe's amount of resistance to erasure.&density of information the stripe can carry.;effectiveness of the stripe's security features.;stripe's ability to be read by a variety of readers.;&&&&n&VI-D-5.0&&&&
|
|
cdc6.096&mcs&0&&Character formation in the ink jet method of printing is developed by &electronically controlled ink droplets.&wire print heads.;laser-beam etching.;magnetized ink.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.097&mcs&0&N&A user is having trouble with a six-part carbon interleaved continuous form because it is running off the pins on the right side. To determine whether the problem is the quality of the forms or a malfunction of the machine, the LEAST desirable approach would be to&order carbonless forms.&take the forms out of the carton and feed them from the floor.;elevate the forms to a higher feeding position so that drag will be reduced.;run the forms backward so that the normal left-hand side will run on right-hand pins.;&&&&n&VI-A-1.0&&&&&1&&&N.
|
|
cdc6.098&mcs&0&&Matrix matching and feature recognition are characteristics of which type of scanner?&Character&Bar code;Mark;Graphic;&&&&n&VI-D-4.0&&&&
|
|
cdc6.099&mcs&0&&In a bar code, the number of characters incorrectly decoded out of the total number of characters scanned can best be described as the &substitution error rate.&first read rate.;transposition error.;print-contrast ratio.;&&&&n&VI-D-3.0&&&&
|
|
cdc6.100&mcs&0&N&Which of the following is the most common problem when using papers with high moisture content on a laser printer?&Paper curling&Toner flaking;Sheets sticking together;Linting;&&&&n&VI-A-2.0&&&&
|
|
cdc6.101&mcs&0&Y&Which of the following sets of printers is LEAST likely to produce framing?&Matrix and photoelectrostatic&Train and chain;Train and matrix;Photoelectrostatic and chain;&&&&n&VI-A-1.0&&&&
|
|
cdc6.102&mcs&0&Y&A dot matrix impact printer forms images by &using print-wires to strike the paper surface through an inked ribbon.&heating thermal paper selectively to its image-threshold point.;fixing toner to the form surface selectively under extreme heat and pressure.;directing microscopic droplets of ink against the paper surface in a preprogrammed pattern.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.103&mcs&0&Y&In normal check-processing procedure, the MICR Amount field is encoded &by the first bank to receive the check.&by the bank on which the check is drawn.;when the check is printed.;when the On-Us field is encoded.;&&&&n&VI-D-2.0&&&&
|
|
cdc6.104&mcs&0&Y&According to the American National Standards Institute (ANSI) and the Canadian Banker's Association (CBA) specifications, what is the MINIMUM height of the clear band on a MICR encoded paper check?&5/8 of an inch&3/8 of an inch;1/2 of an inch;9/16 of an inch;&&&&n&VI-D-2.0&&&&
|
|
cdc6.105&mcs&0&Y&If the legibility of continuous forms is poor on part 1 but adequate on the remaining parts, the problem is most likely caused by &a worn multistrike ribbon.&a faulty carbon.;a worn typeface.;too little impact.;&&&&n&VI-A-1.0&&&&
|
|
cdc6.106&mcs&0&Y&At what point are MICR characters magnetized?&Just prior to being read during processing&Just prior to shipment by the forms manufacturer;When the characters are printed ;When the Amount field is printed;&&&&n&VI-D-2.0&&&&
|
|
cdc6.107&mcs&0&Y&Which of the following thermal transfer ribbons provides the most durable images?&Resin&Multipass wax;Composite;Wax;&&&&n&VI-A-2.0&&&&
|
|
cdc6.108&mcs&0&Y&Which of the following data entry technologies allows the encoding of the greatest amount of data in the smallest amount of space?&Magnetic stripe&Optical mark recognition;One dimensional bar code;Optical character recognition;&&&&n&VI-D-5.0&&&&
|
|
cdc6.109&mcs&0&Y&In a fully automated warehouse, which reader would be best for fast moving packages that are different sizes and have bar coded labels applied to a general location?&Omnidirectional reader&Hand held laser reader;Visible light wand reader;Fixed beam reader;&&&&n&VI-D-4.0&&&&
|
|
cdc6.110&mcs&0&Y&When designing forms for an optical mark reader that incorporates an infrared light source, what must be specified?&Reflective inks for all preprinted readable areas on the scanned ply&The correct bar code symbology being used ;Non-reflective, dark colored papers for the scanned ply;Reflective inks for all preprinted readable areas on the scanned ply;&&&&n&VI-D-1.0&&&&
|
|
cdc6.111&mcs&0&Y&The method of printing a bar code with a heated donor ribbon can be described as what type of printing?&Thermal transfer&Dot matrix;Electrostatic;Direct thermal;&&&&n&VI-A-1.0&&&&
|
|
cdc6.112&mcs&0&Y&In an X-ray filing system utilizing bar coded file folders and identification badges, which of the following forms would be replaced by the bar code reader?&X-ray charge-out form&Physician's order form;X-ray laboratory form;X-ray request form;&&&&n&VI-D-3.0&&&&
|
|
cdc6.113&mcs&0&Y&Which of the following is most critical in scanning a DataMatrix two-dimensional bar code?&Orientation corner&Stop and start bars;Quiet zone;Bull's eye;&&&&n&VI-D-3.0&&&&
|
|
cdc6.114&mcs&0&Y&If a manufacturing company requires a bar code labeling system to be used in a hot, dusty, and humid warehouse climate that could generate over two million labels per year, which of the following printers should be recommended?&Dot matrix line&Desktop laser;Dye sublimation;Direct thermal;&&&&n&VI-A-1 .0& 2.0&&&
|
|
cdc6.115&mcs&0&Y&A common characteristic of direct thermal printer labels is that they &use special heat-sensitive stocks in creating an image.&use a special combination of paper and toner for imaging.;are made of thermal transfer stock which facilitates the transfer of an image.;require special mylar ribbons to create an image.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.116&mcs&0&Y&What is the field on a MICR encoded check which has the highest rejection rate when being machine processed?&Amount field&Auxiliary On-Us field;Transit routing number field;On-Us field;&&&&n&VI-D-2.0&&&&
|
|
cdc6.117&mcs&0&Y&Which of the following is the LEAST appropriate label substrate for printing on a laser printer with a fusion temperature of 400 degrees Farenheit?&Spun olefin&Coated vinyl;Latex impregnated;Matte litho;&&&&n&VI-A-2.0&&&&
|
|
cdc6.118&mcs&0&Y&Most electrophotographic printers transfer toner from the imaging drum by applying an electrostatic charge to the&paper.&fuser rollers.;cleaning wand.;impression cylinder.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.119&mcs&0&Y&The next three questions are based on the following diagram of a printer with a rear feed. DIAGRAM Which of the following problems is most likely to occur with printing a six-part crimped form?&Misregistration&Insufficient gate clearance;Insufficient stub margin clearance;Tenting;&&&&n&VI-A-1.0&&&&
|
|
cdc6.120&mcs&0&Y&When printing a two-part form with a blown-on label, which of the following problems is most likely to occur?&Predispensing&Misregistration;Poor manifolding;Adhesive buildup;&&&&n&VI-A-1.0&&&&
|
|
cdc6.121&mcs&0&Y&When printing a four-part form that will be burst and remain together after processing, which of the following would be best to use?&Tape lock&Line glue;Fugitive glue;Crimping;&&&&n&VI-A-1.0&&&&
|
|
cdc6.122&mcs&0&Y&Proper design for electronic storage of a printed document is most important because &some design elements interfere with electronic image scanning.&output will be on microfiche.;screens are defined in terms of screen percentage and lines per inch.;the contents of a document can be electronically distributed to a network.;&&&&n&VI-D-4.0&&&&
|
|
cdc6.123&mcs&0&Y&The next two questions are based on the following diagram. DIAGRAM Which of the following is indicated by A?&Gate clearance&Print head clearance;Stub margin clearance;Pin diameter;&&&&n&VI-A-1.0&&&&
|
|
cdc6.124&mcs&0&Y&Which of the following is indicated by B?&Stub margin clearance&Distance to the first print line;Pin diameter;Gate clearance;&&&&n&VI-A-1.0&&&&
|
|
cdc6.125&mcs&0&Y&When designing forms in which variable data are to be scanned into electronic imaging systems, which of the following is the most important design feature to incorporate?&Nonread inks&Intricate graphics;Continuous construction;Halftones;&&&&n&VI-D-4.0&&&&
|
|
cdc6.126&mcs&0&Y&The following form will be personalized on a high-speed laser printer and MICR printed in-line. What is the primary concern that the bank of first deposit will have relative to processing the check certificates? DIAGRAM&Readability of MICR line&3 1/2 inch dimension of check height;Perforated lead and bottom edge of check;Width of clear band designed for MICR encoding;&&&&n&VI-D-2.0&&&&
|
|
cdc6.127&mcs&0&Y&Which of the following is the best type of construction to specify for an envelope used in high-speed inserting equipment?&Open side, diagonal seams, intermittent glue strip&Open side, side seams, full glue strip;Open end, diagonal seams, full glue strip;Open end, side seams, intermittent glue strip;&&&&n&VI-B-5.0&&&&
|
|
cdc6.128&mcs&0&Y&Which of the following methods used solid hot-melt ink?&Inkjet phase change&Ion deposition;Digital color offset;Direct thermal;&&&&n&VI-A-2.0&&&&
|
|
cdc6.129&mcs&0&Y&Why are rubber rollers employed on some bursters?&To reduce unwanted manifolding&To reduce machine noise;To prevent slippage at different roller speeds;To reduce static;&&&&n&VI-B-1.0&&&&
|
|
cdc6.130&mcs&0&Y&Thermal transfer printers transfer ink to the receptor material from the&donor ribbon.&latent image.;toner drum.;charged area.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.131&mcs&0&Y&Which of the following is a characteristic of direct thermal printing?&Is not recommended for applications exposed to sunlight or heat&Uses a heated print head to transfer ink from ribbon to substrate;Uses plain bond paper;Cannot be used to print bar codes;&&&&n&VI-A-2.0&&&&
|
|
cdc6.132&mcs&0&Y&When using a thermal transfer printer, which of the following is the most appropriate application of on-demand printing?&Bar code tags&Cheshire labels;Business cards;Purchase requisitions;&&&&n&VI-A-2.0&&&&
|
|
cdc6.133&mcs&0&Y&Which of the following thermal transfer ribbons provides the most durable images?&Resin based ribbon&Multipass wax based ribbon;Composite ribbon;Wax based ribbon;&&&&n&VI-D-2.0&&&&
|
|
cdc6.134&mcs&0&Y&In selecting a medium on which to print a bar code, what is the most important property to consider?&Reflectance&Smoothness;Scruff resistance;Opacity;&&&&n&VI-D-3.0&&&&
|
|
cdc6.135&mcs&0&Y&Which of the following is a non-impact full color printer technology which melts crayon-like ink blocks of process color?&Phase change ink jet&Wax thermal transfer;Dye sublimation;Electrophotography;&&&&n&VI-A-2.0&&&&
|
|
cdc6.136&mcs&0&Y&Electrophotography is best known as &laser.&ink jet.;direct thermal.;thermal transfer.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.137&mcs&0&Y&Skunk marks on Optical Mark Recognition (OMR) forms are used to &tell the computer which program to execute.&see if a form is positioned correctly.;tell the scanner to scan the response on that line.;designate the long edge of the OMR form.;&&&&n&VI-D-1.0&&&&
|
|
cdc6.138&mcs&0&Y&One of the most attractive archival aspects of using WORM drives in records storage and retention systems is that &once an image is stored it cannot be altered.&it holds more data compared to a comparably sized tape drive.;data access times are much faster than magnetic media thus allowing faster retrieval of data.;so much data can be stored on one drive that it is easy to reindex the disk and keep related files together.;&&&&n&VI-D-5.0&&&&
|
|
cdc6.139&mcs&0&Y&Which of the following non-impact full color technologies employs the use of toners to create the desired image?&Electrophotography&Wax thermal transfer;Ink jet;Dye sublimation;&&&&n&VI-A-2.0&&&&
|
|
cdc6.140&mcs&0&Y&Which of the following type sizes and styles will be most easily scanned by OCR software?&12 pt Helvetica&6 pt Geneva;7 pt Courier;8 pt Futura Italic;&&&&n&VI-D-1.0&&&&
|
|
cdc6.141&mcs&0&Y&To process two-wide forms on horizontal decollators, the decollator must be equipped with &a center slitter.&a burster attachment.;a cross perforation blade.;an imprinter.;&&&&n&VI-B-2.0&&&&
|
|
cdc6.142&mcs&0&Y&Which of the following technologies uses inks that are quickly changed from solid to liquid to solid during the printing process?&Phase change&Magnetography;Electrophotography;Direct thermal;&&&&n&VI-A-2.0&&&&
|
|
cdc6.143&mcs&0&Y&Thermal transfer printers transfer ink from which of the following to the receptor material?&Donor ribbon&Latent image;Charged area;Toner drum;&&&&n&VI-A-2.0&&&&
|
|
cdc6.144&mcs&0&Y&Inkjet printers can NOT be used to &manifold multiple-part forms.&print pressure-sensitive labels.;image overhead transparencies.;process paper with a textured finish.;&&&&n&VI-A-2.0&&&&
|
|
cdc6.145&mcs&0&Y&If an application calls for a bar coded label which is likely to be exposed to abrasion and direct sunlight, which of the following combinations is preferable?&Thermal transfer printing with a resin ribbon&Direc thermal printing on a 100 lb tag substrate;Thermal transfer printing with a multi-pass ribbon;Direct thermal printing with a 300 DPI thermal printer;&&&&n&VI-A-2.0&&&&
|
|
cdc6.146&mcs&0&Y&What type of label stock must be used by long range (fifteen to thirty feet) bar code scanners?&A retroflective stock containing glass beads that act as reflectors&A white matte finish which will ensure the proper contrast needed at a long distance;A laminated foil with a dull finish;A thermo sensitive stock which must be used to provide a clear contrast for the bar code reader;&&&&n&VI-D-3.0&&&&
|
|
|